Completely New Prolific Tool Holders From Iscar Direct The Way In Machining Efficiency

Iscar's Heliturn model features a unique, double-sided insert with 4 cutting edges for Fast Metal Removal (FMR) turning. The cutting edge Heliturn is a tangentially clamped insert using a exclusive helical shaped cutting edge, useful for large depths of cut and higher than typical feed rate. The LNMX...-HT Heliturn insert is screw-clamped into the SLANR tool holder and held by the TLN ..-HT carbide seat. This seat has ground surfaces on the top and bottom, to ensure perfect contact of the insert with the tool holders. The upper rake face of this insert is mounted level with the top of the tool holder to permit chips to flow across the insert, without being interfered by clamps or the tool holder body. The 4 curved helical cutting edges establish positive radial rake angles and soft penetration into the material being cut. The lower forces and smaller loads assure better tool longevity, elevated stability and the ability to use very massive depths of cut and greater feeds. The chipformer, manipulates and breaks the chip into rib type curved pieces which can effectively be removed from the cutting area. The insert has a frontal clearance angle of 3.7 with a 6 side clearance angle to allow machining to a 90 shoulder. Depth of cut up to .315" and facing depths to .126" at up to .047" IPR are attainable with Heliturn.

When compared to CNMG/M 16... or WNMG/M 13... insert sizes with the similar corner radius, much enhanced tool life can be foreseeable when using the LNMX 1506..-HT insert. Iscar has recently included a smaller size to the Heliturn family - the LNMX 1104..R/L-HT insert and tool holder for the medium application range of up to .197" depth of cut. The brand new insert features all of the blessings of the larger insert. This enhances the economical advantage in the medium machining application area. When compared to CNMG/M 43. 12... or WNMG/M 43. 08... insert sizes with the same corner radius, a far better tool life can be foreseen. The inserts are accessible in .031, .047 and .063" tool nose radii. Heliturn inserts are obtainable in the most advanced carbide grades: IC9025, IC3028 , IC428, IC907, and IC908.

The external tool holders are presented in 1, 1.25 and 1.5" shank sizes. Boring bars are offered in 1, 1.25 1.5 and 2" bar sizes. Also obtainable are exchangeable heads. These tool holders have Iscar's unique Hard Touch coating, which extends holder life and hinders corrosion. As a result of the placement of this insert, machining next to the tailstock is likely.

The high positive rake angle of these tools allows 10-15% less power usage than conventional tool holders at the same parameters.

By using Iscar's Heliturn tools, tremendous cost savings and profitability in lathe procedures is guaranteed.

A Brand new 80 Degree Rhombic Insert with high helical cutting edge for high metal removal rates Iscar is unveiling the CNMX 1207..-HTW insert family. The unique insert has a very positive radial, helical cutting edge and a positive rake angle; a succession which considerably reduces the cutting forces. The insert's corner has a wiper configuration which supplies high surface finish even at high feed conditions, which in abundant occasions can eliminate a finishing cut. The corner angle is 88 degrees which provides elevated strength. The CNMX inserts were developed for heavy machining applications. Their specific design ensures dependable, fast metal removal when using 80 degree rhombic inserts. They can be mounted on any regular tool holder that carries standard CNMG inserts, but the seat has to be replaced with a special seat: TCH 4. Iscar's R-clamp tool holders are highly favored for heavy machining applications.

Which Kinds Of Things Do Machinists Utilize During Their Job?
The things machinists do and utilize is kind of a mystery to the remainder of the world. We know that these workers are necessary, however we are not one hundred percent certain regarding why exactly we require them.

Buying A Megger Tester: Most Excellent Practices
A Megger tester is a device that is commonly used in electrical contracting to determine if the system has been properly installed.

Why People Prefer Digital Caliper.
Here are some of the top reasons for considering a digital caliper. Depending on the size of your requirement you can get a caliper for about $49-100. A battery is used to power the device. It lasts and so you do not have to worry about replacing the battery.

Woodworking Made Much Easier With Grizzly Equipments
Woodworking is a craft that requires adequate skill and creativity. The skill of a woodworker is translated to the wood with the use of appropriate wood carving tools. One brand that is popular among Northern Tools customers is Grizzly Woodworking tools.

Kreg Jig Projects For Newbies
One of the leading brands when it comes to efficient and convenient tools is the Kreg Jig. In the products of Kreg Jig, the most widely used are the pocket hole jig and the kreg joint. The pocket hole is so easy to use that some described it as dummy proof.